CV Power supplies 24 V

Remove the limitations when you install light outside, with OPTOTRONIC CV 24 V power supplies. Ruggedly built, if you need a constant voltage source that can cope with damp or wet conditions and extremes of temperature, then a product from this range could be just what you need. These drivers are suitable for use in tight, flat luminaires and in suspended ceilings, and may be used outdoors (only within suitable luminaires). If you are creating signage, OPTOTRONIC CV 24 V power supplies work well with OSRAM signage LED modules such as BackLED and BoxLED, and in other settings they can be paired with suitably robust and protected modules such as LINEARlight Flex Protect, to give great performance, reliability and efficiency.

CV Power supplies 24 V

Product data sheet
Product family features
  • DC mode functionality
  • Type of protection: IP66 and IP67
  • Surge protection: up to 4 kV (L-N) / 6 kV (L/N-PE)
  • Wide operating temperature range: -30…+55 °C
  • Lifetime: up to 50,000 h (temperature at max. tc )
Product family benefits
  • Large range of products from 20 W to 250 W
  • Installation in very cold and hot environments
  • Very stable output power
  • High electronical reversible short-circuit, overload, overtemperature protection
  • Smart Power Supply: boosting power to turn on cold LEDs
  • Independent installation possible
Family datasheet

Electrical data

Nominal input voltage 220…240 V
Mains frequency 50…60 Hz
Input voltage AC 198…264 V

VAC

Input voltage DC 176…274 V

Permitted voltage range

Total harmonic distortion < 20 %
Power factor λ 0.95/0.90

Full load at 230 V/Half load at 230 V

ECG efficiency 85 %

At full load and 230 V

Device power loss 8.0 W

Maximum

Inrush current 45 A

twidth = 80 µs (measured at 50 % Ipeak)

Max. ECG no. on circuit breaker 10 A (B) 12
Max. ECG no. on circuit breaker 16 A (B) 19
Max. ECG no. on circuit breaker 25 A (B) -
Surge capability (L-N) 1 kV
Nominal output voltage 24 V

+0.9/-0.5 V

U-OUT (working voltage) 24 V
Nominal output power 50 W

Partial load 0…50 W

Galvanic isolation SELV
Galvanic isolation primary/secondary 3.75 kV

SELV

Dimensions & weight

Product weight 290.00 g
Cable cross-section, input side 0.75…1.5 mm²

Solid or flexible leads

Cable cross-section, output side 0.5…1.5 mm²

Solid or flexible leads

Wire preparation length, input side 10 mm
Wire preparation length, output side 10 mm
Cable/wire length, input side -
Cable/wire length, output side -
Length 242.0 mm
Height 16.0 mm
Width 40.0 mm

Colors & materials

Casing material Plastic

Temperatures & operating conditions

Ambient temperature range -20…+45 °C
Maximum temperature at tc test point 95 °C
Max.housing temperature in case of fault 110 °C
Permitted rel. humidity during operation 5…85 %

Maximum 56 days/year at 85 %

Lifespan

ECG lifetime 50000 h

At Tcase = 80°C at Tc point / 10% failure rate

Additional product data

Encapsulated No

Capabilities

Dimmable No

With OPTOTRONIC dimmers

Overheating protection Automatic reversible
Overload protection Automatic reversible
Short-circuit protection Automatic reversible
No-load proof Yes
Suitable for fixtures with prot. class II
Type of connection, output side Screw terminal

Certificates & standards

Approval marks – approval CE / CB / RCM / ENEC 18
Standards Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3-2/Acc. to IEC 61547
Protection class II
Type of protection IP20

Logistical data

Temperature range at storage -30…85 °C
Commodity code 850440829000

EAN

Unit
Piece

Dimension l x w x h

Weight

Volume

4052899905566 UNV
1
290.00g
4052899905597 VS
20
288mm x 134mm x 248mm 4758.00g 9.57dm³
Maximum number of LED modules per ECG 22
Maximum number of LED modules per ECG 16
Maximum number of LED chains per ECG 1
Maximum number of LED modules per ECG 16
Maximum length of LED module per ECG 13.8 m
Maximum length of LED module per ECG 12.15 m

EAN

STK number

4052899905566 4030200